What is asbestos?
back
Asbestos is a group of naturally occurring minerals. The three most common types of asbestos are: a) chrysotile b) amosite c) crocidolite
Asbestos is commonly used as an acoustic insulator, thermal insulation, fire proofing and in other building materials. Asbestos fibers are incredibly strong and have properties that make them resistant to heat. Asbestos is often found in ceiling tiles, pipe and vessel insulation, blown on to structural beams and ceilings, in floor tile, linoleum and mastic.
Why is asbestos a hazard?
back
Asbestos is made up of microscopic bundles of fibers that may become airborne when distributed. These fibers get into the air and may become inhaled into the lungs, where they may cause significant health problems. Researchers still have not determined a "safe level" of exposure but we know the greater and the longer the exposure, the greater the risk of contracting an asbestos related disease. Some of these health problems include:
When is asbestos a hazard?
back
Asbestos is not always an immediate hazard. In fact, if asbestos can be maintained in good condition, it may be acceptable to leave it alone and periodic surveillance performed to monitor it’s condition. It’s only when asbestos containing materials are disturbed or the materials become damaged that it becomes a hazard. When the materials become damaged, the fibers separate and may then become airborne. In the asbestos industry, the term " friable" is used to describe asbestos that can be reduced to dust by hand pressure. " Non-friable" means asbestos that is too hard to be reduced to dust by hand. Non-friable materials, such as transite siding and floor tiles are exempt from certain portions of state regulations, provided it does not become friable. Machine grinding, sanding and dry-buffing are ways of causing non-friable materials to become friable.
How are asbestos containing materials maintained?
back
Friable asbestos can be maintained in place utilizing several techniques. Encapsulation involves applying a thick layer of an encapsulant, much like latex paint, that binds the surface of the material together and prevents the release of fibers, however this usually is not enough of a coating to protect against damage. When damage is likely to occur, removal may be the best option.
When is it necessary to remove asbestos containing materials?
back
There is no law that says asbestos has to be removed. It is only when the material can no longer be maintained in good condition and /or the airborne concentrations of asbestos are measured to be too high, or when the building is to be demolished or renovated, that removal may become the only option.
In these instances, asbestos may only be removed by Licensed Asbestos Abatement Contractors, utilizing Licensed Workers and Supervisors. These requirements do not necessarily apply to private residences.
When is it required to have a building inspection or survey?
back
There are now state and federal regulations that require all material that has not been tested to be presumed to contain asbestos. Only inspection and sampling may rebut the required presumption.
Any building owner who is renovating or demolishing a building is required by federal law to have their buildings surveyed for asbestos containing materials. Buildings are not permitted to be demolished if there is asbestos present. Also, public and private schools, K-12, are required by AHERA, the Asbestos Hazard Emergency Response Act, to be inspected and have a management plan prepared, which is to be maintained and available for public inspection.
How is asbestos removed?
back
When removal is conducted, a licensed contractor must notify the appropriate regulatory agency ten days in advance of removal. Some projects, are required to have a project design that details how the contractor will perform the removal.
Upon approval from the appropriate regulatory agency, workers construct a containment, sealing all possible entries and exits to prevent air from escaping from the containment. Containments are maintained under negative pressure and the air is exhausted through special filters that make sure the air exhausted is safe. A decontamination unit is built on to the containment, where workers change into disposable suits and respirators upon entering, and shower before exiting the work area, so as not to contaminate the area around the containment by tracking out asbestos on their clothes or body. Next, the contractor wets down the material, which helps reduce the airborne fiber count. As the material is wetted, it is scraped from the surfaces and collected in specially labeled disposal bags. When a bag is full, it is sealed well, wiped down and placed into a second bag, which is also sealed. The bags are placed in a load-out chamber to await transfer to a specially lined waste trailer. When all the visible material is removed and bagged, the bags are loaded out to the waste trailer.
At this point, the contractor must have a qualified consultant perform a visual inspection and air test, to ensure that the area is safe to reoccupy. After the clearance monitoring is conducted and the air counts are within the accepted levels, only then is the containment removed.
Other abatement techniques, such as removal of pipe insulation via a glove-bag or a mini-containment, are also conducted following procedures outlined by the appropriate regulatory agencies
Where does asbestos go after it is removed?
back
After removal, the sealed bags are transported by a licensed, insured, abatement contractor or a licensed asbestos hauler, to an EPA Approved Landfill, where it is buried. Disposal manifests are generally required to ensure the waste arrived at the landfill for appropriate disposal. Under the authority of the EPA, there is a list of landfills approved to take asbestos containing waste.
How can I tell if I have Asbestos in my Building?
back
The only way to tell if a building material contains asbestos is to have a representative piece(s) analyzed. You can send a licensed inspector to take bulk samples to the laboratory, where they are analyzed under the microscope to determine the content. Both state and federal regulations require building owners to presume that any suspect material is asbestos until a laboratory analysis is conducted. Any material that contains less than one percent asbestos is considered non-regulated. In some cases, it is possible for you to send us a small sample for analysis. Please contact us for details.
Who do I call if I have a concern?
back
If you have any concerns or would like to schedule an appointment to discuss your situation call Diamond Environmental Service at 574.246.9902 or click the button below and complete our convenient online form.
What are molds?
back
Molds are small microscopic organisms, present virtually everywhere, inside and outside. Molds are fungi and are needed to break down dead material and recycle nutrients in the environment. Mold needs a food source to grow-any organic material such as leaves, paper, wood, and moisture. Since molds grow by digesting the organic material, they will gradually destroy whatever they grow on. Mold can often be seen in the form of discoloration, frequently green, gray, brown, or black and also white and other colors. Molds are very tiny and lightweight, and travel easily through the air.
What are sources of moisture in my home?
back
How can I be exposed to molds?
back
You are exposed to some mold every day, usually by touching, eating or breathing it. When mold is growing on a surface, spores can be released into the air where they can be easily inhaled. A person who ingests or inhales a large number of spores may suffer adverse health effects.
What health effects can be caused by exposure to mold?
back
Molds can produce health effects through inflammation, allergy, or infection. Allergic are the most common following mold exposure. These include:
Should I be concerned about mold in my home?
back
When airborne mold spores are present in large numbers, they can cause skin irritations, allergic reactions, asthma episodes, infections and other respiratory problems for people. Exposure to high spore levels can cause the development of an allergy to the mold. Mold also can cause structural damage to your home.
Can my home be tested for mold?
back
Yes, if the mold contamination is extensive, it can cause high air borne spores exposures, which can cause health problems. Homeowners must hire a contractor to test their homes. Even if testing is done, no standards exist to judge what are acceptable amounts of mold. Testing cannot determine whether health effects will occur. Mold is normally found outdoors and counts fluctuate from day to day depending on the season. Due to the uncertainties associated with testing for molds. If you can see or smell mold, testing is usually not necessary.
What is stachybotrys?
back
Stachybotrys is a greenish-black, slimy mold found only on cellulose products (such as wood or paper) that have remained wet for several days or more. Stachybotrys doesn't grow on concrete, linoleum or tile. According to the U.S. Centers for Disease Control; and prevention (CDC), all molds should be treated the same with respect to potential health risks and removal. All molds should be handled with caution.
In 1994, the CDC investigated whether exposure to stachybotrys might be related to pulmonary hemorrhage, also known as bleeding lungs, in infants in Cleveland, Ohio. They concluded that there was a strong association between stachybotrys and bleeding lungs.
My belongings were soaked when my basement flooded. What should I do?
back
Carpets, paper and other absorbent materials can grow mold after getting soaked. In general, it is best to throw out those items. Other items made of glass or metal should be cleaned and disinfected.
How can I clean moldy surfaces?
back
1. The surfaces first need to be cleaned with soap.
· Use non-ammonia soap or detergent in hot water and scrub the entire area affected by the mold. Never mix bleach with ammonia; the fumes are toxic.
2. The next step is to disinfect surfaces to help prevent mold from coming back.
How can I reduce my exposure to the mold while cleaning it up?
back
During the cleanup of molds, many spores may be released into the air. Mold counts in air are typically 10 to 1, 000 times higher than background levels during the cleaning and removal of mold-damaged materials. To prevent health effects, there are several ways you can protect yourself while cleaning up the mold.
If you have any concerns or would like to schedule an appointment to discuss your situation call Diamond Environmental Service at 574.246.9902 or click the button below and complete our convenient online form.